The smart parts
are all hidden.

Two electrodes sealed in the wall, the circuit sealed in the base. From outside, it is just a white cup.

This device cannot show 3D models. Please open the page in a browser that supports WebGL.
14 mLVolume sensed by the cup · illustrative

With battery: broadcasts over Bluetooth at a set interval while worn, and alerts you when nearly full.

Angle

Drag with one finger to rotate in any direction · pinch to zoom, two-finger drag to pan · double-tap to reset

A proven
method.
Capacitive level sensing. One electrode strip is sealed into each side of the wall; as the fluid rises, the capacitance changes at that height. A motion sensor in the base corrects for tilt. This is a common level-measurement technique, and it was already disclosed in smart-cup patents a decade ago.
From outside,
invisible.
Milk-white silicone fully covers the electrodes. No wires, no windows, no seams on the wall. Tap "See inside" to reveal them.
Folds,
and comes out.
The electrodes are serpentine traces that stretch and fold with the wall. A small bump on each side of the rim shows your fingers where to fold, and the crease avoids the electrodes. A small loop and two grip dots on the base make the cup easy to find, pinch and remove.
One base
holds the rest.
The base is a small capsule that is sealed and tested on its own, then fitted into the cup. From the bottom up: a temperature sensor close to the outer surface, the charging coil, a magnetic shield, the circuit board (chip, motion sensor and memory), the small battery, and the Bluetooth antenna on top. Each side of the wall has two layers: the inner one measures, the outer one shields against interference from the body. The electrodes enter from both sides through soft strain-relief sleeves so folding does not tear them. Tap "See inside" to see each layer.
Two versions,
your choice.
With battery: a very small rechargeable cell and Bluetooth in the base. It broadcasts at the interval you set while worn and alerts you at your chosen flow level. No battery: a supercapacitor replaces the cell. Charged in the case, it records for a period of time. There is no Bluetooth in the cup; data syncs when the cup is back in the case, and there is no alert while worn. It is simpler, cheaper and lighter on compliance. Both versions share the same shape and the same case.
Flip lid, magnetic,
tight seal.
A small round aluminium case, opaque. The lid hangs on a rear hinge, opens one-handed and snaps shut magnetically. A silicone gasket seals the seam. As soon as the lid opens, the case starts syncing data.
Close the lid,
it sanitises and dries itself.
UV lamps sit in the lid and shine down into the cup; the white liner reflects light onto the outside of the cup. A low-temperature heater film wraps the middle of the case wall, and moisture leaves through a waterproof breathable membrane on the back of the lid. The moment the lid opens, the UV lamps switch off. Tap "UV demo" to watch it run.
Structure,
layer by layer.
From the bottom of the case up: non-slip foot ring, a non-metal base plate (Bluetooth leaves through it), a weight ring, battery, main board, magnetic shield, then the charging post. Under the liner sits a fixed aluminium bell-shaped shell: its inner surface is polished to reflect UV back onto the cup; two rings of UV LEDs in its side shine through the liner onto the cup wall; the heater film and a temperature sensor wrap the outside. In the lid, a UV board sits in a sandwich layer and shines through a flush UV-transparent window; its flex cable passes through the hinge and runs down the back wall to the main board. A pair of magnets at the front edge only hold the lid shut, and a sensor beside them cuts the UV the moment the lid opens. Tap "Cut case open" to see it.
A liner
you can take out and wash.
The cup holder in the middle is a sealed charging post fixed to the case floor, with the coil at its top, right under the base of the cup. The liner follows the shape of the cup about 4 mm away. It is made of 0.5–0.8 mm frosted fluoroplastic (FEP) that lets UV through, with a rigid rim frame you pinch when taking it out or putting it back. The liner is a replaceable part. The front of the lid has a shallow recessed finger groove, and the hinge is hidden inside the wall with nothing sticking out.

Concept design, not an engineering drawing or a circuit design. Capacitive level sensing is a mature principle, but how accurate it can be with thick fluid containing clots, inside the body, has to be confirmed by prototypes and comparison tests. A cup with a battery probably cannot be boiled, so cleaning instructions must change accordingly. Battery safety in the cup and comfort of a solid base while worn also need testing, as do Bluetooth range through the body and battery life. UV sanitising effectiveness, the ageing effect of UV and heat on silicone, and whether the heating temperature is safe for the battery in the cup all need testing; claiming "sanitising" also requires an efficacy test report. The magnets sit close to the circuit in the base, so their effect on the coil and sensors must be assessed. Readings are illustrative, scaled to a full cup of about 30 mL.