// HARWIN.COM 
 
 
 
 
 
 
 
 
 
 
 
 
5 
Z20-320 
M20-118 
 
Instruction Sheet 
IS-15 
Hand Crimp Tool Z20-320 

2 
Issue: 8   Date: 01/02/2023   C/Order: 32102 
IS-15 
Instruction Sheet for Z20-320 Hand Crimp Tool
CRIMP CONTACT INFORMATION 
▪ M20-1160042 ................ 2.54mm Pitch Crimp Contacts, Reeled, Gold 
▪ M20-1160046 ................ 2.54mm Pitch Crimp Contacts, Reeled, Tin 
▪ M20-1180042 ................ 2.54mm Pitch Crimp Contacts, Loose, Gold 
▪ M20-1180046 ................ 2.54mm Pitch Crimp Contacts, Loose, Tin 
 
GENERAL INFORMATION 
The Z20-320 Hand Crimp Tool consists of a ratchet mechanism hand tool and a set of jaws. The 
jaws comprise of upper and lower crimp dies. 
The contact is correctly crimped when the tool is free to open at the fully closed position, i.e. 
when the ratchet releases. 
 
CRIMPING PROCEDURE 
1. Ensure that the wire to be crimped is within the specified range of sizes for the contact 
and the crimp tool. Failure to use the specified wire size will result in poor quality crimps 
and possible tool damage. 
Wire Gauge Minimum pull-off force (N) 
30 AWG 9 
28 AWG 11 
26 AWG 18 
24 AWG 29 
22 AWG 45 
 
2. Strip the wire insulation to the dimensions shown below. Care should be taken to avoid 
cutting or displacing the conductors. If the conductors are displaced, they may be re-
aligned with a gentle twist. We recommend that when the wire is stripped, it is clamped or 
supported close to the stripping area - this will prevent insulation slippage. Suitable wire 
strippers (such as a PTFE wire stripper) must be used. 
 
 
4.0mm max Ø1.7mm max 
 
3. Make certain that the hand crimp tool is in the fully open position, and that the jaws are 
free from dirt and debris. 
4. If the socket is on a reel, break or cut off a contact from the strip of bandolier. 
5. Place the contact into the correct crimp cavity in the fixed jaw. The markings on the jaw 
indicate the correct crimp cavity according to the wire size being used. The orientation of 
the contact is with the crimp end uppermost, with the open side of the crimp facing 
towards the moving jaw. 
3 
Issue: 8   Date: 01/02/2023   C/Order: 32102 
IS-15 
Instruction Sheet for Z20-320 Hand Crimp Tool
6. Partially close the crimp tool until the wire stop comes across the face of the fixed jaw. 
7. Take the pre-stripped wire and insert it into the contact so the conductors and insulation 
are positioned in the crimp. The conductors should be touching the wire stop.  
 
 
8. Keeping the cable steady in the crimp, fully close the hand crimp tool until the ratchet 
releases. Let the crimp tool open. 
9. After crimping remove the assembly. The process is then repeated for each crimp required. 
RECOMMENDED CRIMP HEIGHTS 
Contact Wire Gauge Recommended Conductor 
Crimp Height (mm) 
M20-11600XX, 
M20-11800XX 
22-24 AWG 0.86±0.03 
26-30 AWG 0.72±0.03 
 
TOOL MAINTENANCE 
1. Keep the tool clean and free from dirt and foreign matter. Ensure that all retaining pins and 
clips are in place before use, and that signs of wear are not visible. If the pivots are worn, 
the tool must be replaced, or crimp integrity will be compromised. 
2. Oil at all pivots and bearings using a light cycle oil. 
3. At regular intervals, check the crimp tool jaws for wear or damage, and inspect sample 
crimps for form and function. Minimum pull-off forces (as shown in the previous table) 
should be achieved when sample is tested. If forces are not achieved, calibrate the tool. 
  
4 
Issue: 8   Date: 01/02/2023   C/Order: 32102 
IS-15 
Instruction Sheet for Z20-320 Hand Crimp Tool
TOOL CALIBRATION 
The operating force at the point shown should be 150N (15kg, 33lbs) min. 
 
5 
Z20-320 
26-28 
24-26 
22-24 
M20-118 
40mm 
 
If adjustment of the tool becomes necessary due to pull-off forces not being maintained, the 
following instructions should be followed. 
1. Remove Hex socket grub screw using a 2mm A/F Hex key. 
2. Using a screwdriver, turn the numbered wheel via the wheel adjustment screw. To increase 
the pre-load (and therefore the crimp pull-off force), turn the screw until the next number is 
shown. Even numbers are found by turning the screw clockwise, odd numbers are anti-
clockwise. Turn the screw until the required number is level with the Hex socket grub screw 
hole. 
 
5 
Z20-320 
26-28 
24-26 
22-24 
M20-118 
Hex socket grub screw 
Wheel adjustment screw 
 
3. Re-fit the Hex socket grub screw and tighten. 
4. Check the operating force as shown at the top of the page. Repeat the procedure if the 
force is incorrect. 
If the adjuster is set to maximum, and operating force is still not achieved, the tool has 
finished its working life (50,000 crimps minimum) and will need replacing. 
 
