PCBA PARTNER
EN
English中文Deutsch日本語Français

Engineering reference · Automotive lighting electronics

Automotive LED headlamp driver.HL-4A design reference.

A 12 V vehicle-supply driver board for a four-function LED headlamp: low beam, high beam, daytime running light and turn indicator. This page shows how the power stage, LED drivers and CAN FD control are put together, what has been checked, and what has not been tested yet.

  • Status: design complete, prototype validation not yet executed
  • 4-layer board, 110 × 90 mm
  • CAD source: KiCad

From 12 V battery to four LED channels

Short answer: the battery feeds a protected input, a two-phase boost stage makes a 48 V bus, and two dual-channel buck drivers turn that bus into four constant-current LED outputs. A microcontroller sets the currents over SPI and talks to the vehicle over CAN FD.

HL-4A functional architecturePOWERSIGNAL / CONTROL
Power path
Input, 12 VSurge, filter, reverseTVS, pi filter, ideal diode
Boost48 V busTwo-phase, 400 kHz per phase
LED drive4 buck channels2 × dual-channel drivers
Control path
VehicleCAN FDESD-protected bus
MCUMSPM0G3507State machine and derating
SPIDriver setupCurrent, faults, limp-home

Why the board is built this way

Each choice below was made to survive a vehicle supply, or to keep the first prototype buildable.

Input

Surge and reverse protection

A bidirectional TVS, a pi filter and an ideal-diode controller sit in front of everything else. The input switch is an 80 V part, chosen so the first ISO 7637-2 pulse (63 V and above) stays inside its rating.

Boost

Two interleaved phases

Splitting the 48 V stage into two phases at 400 kHz each shares the current between two inductors and two switches, and cuts input ripple.

LED drive

Buck frequency kept out of AM

The buck channels run at about 380 kHz (312 to 487 kHz across tolerance). An earlier setting near 650 kHz would have landed in the AM medium-wave band, so it was changed.

Safety

Low beam stays on

The intended behavior: if the CAN link times out (500 ms) while the ignition or a hard-wired request is present, the low beam stays on. If the MCU stops, the drivers fall back to a limp-home mode that holds the low beam.

Thermal

Derating by channel

Low supply voltage and high board or LED temperature reduce or shut off the high beam first. The low beam is not switched off for board temperature.

Assembly

Parts the assembler may not stock

The power inductors and the CAN common-mode choke are not in the assembler's stock library, so they are supplied as consigned parts. Wire-out connectors are fitted by hand after assembly.

Main devices on the board

The prototype BOM uses a few non-automotive-grade equivalents to cut cost and lead time. They are marked to be changed back to automotive-grade versions for production.

FunctionDeviceNote
Reverse-polarity protectionLM74700-Q1 ideal-diode controllerWith 80 V logic-level MOSFET
Surge clampSMCJ33CA TVSPrototype uses the non-Q version
48 V boost controllerTPS92682-Q1Two phases, 100 V MOSFETs
LED current drivers2 × TPS92520-Q1Four buck channels in total
MicrocontrollerMSPM0G3507 (LQFP-48)Prototype uses the non-Q1 version
CAN protectionPESD2CANFD24L-Q ESD diode, 51 µH common-mode chokeCAN FD, 500 k / 2 M
Power inductorsCoilcraft XAL seriesConsigned to assembly

Part numbers are listed so engineers can judge the design. Availability and substitutes change; confirm stock before you order.

What the files show today

These numbers come from the board file and the DRC and ERC reports for the current revision.

4 layers1.6 mm, 70 µm outer and 35 µm inner copper
110 × 90 mmBoard outline
0 errorsDRC, with 0 unconnected pads
0 / 0ERC errors and warnings

The DRC report lists 23 warnings. All of them are silkscreen items: 3 clipped by the board edge and 20 clipped by solder mask. A custom rule keeps at least 0.3 mm clearance from high-current pours to other nets and to the board edge.

Done, and not done yet

This is a design reference, not a qualified product. Please read it that way.

Done

  • Schematic in four sheets, with calculation-sheet changes folded in
  • Four-layer layout, DRC and ERC run
  • BOM and placement files prepared for assembly
  • First-pass firmware structure and CAN message definitions

Not done yet

  • Prototype build and bench measurements
  • ISO 7637-2 pulse and EMC testing
  • Thermal and photometric testing
  • Firmware run on hardware

Tell us about your lighting project

Bring your driver to a design review.

Share the supply range, LED load, number of channels, interface and quantity. We will reply within 1 business day after we confirm receipt.